[email protected]

ASTM A194 / A194M - 20a Standard Specification for Carbon

ASTM A194 / A194M-20a, Standard Specification for Carbon Steel, Alloy Steel, and Stainless Steel Nuts for Bolts for High Pressure or High Temperature Service, or Both, ASTM International, West Conshohocken, PA, 2020, astm ASTM A194 Grade 8CA Nuts, Heavy Hex Nuts, Hex Nuts Standard Specification for Carbon and Alloy Steel Nuts for Bolts for High Pressure or High Temperature Service, or both. ASTM A194 specification covers a variety of carbon, alloy, and martensitic stainless steel nuts in the size range 1/4 through 4 in. and metric M6 through M100 nominal.

ASTM A194 Grade 8T Specification - Boltport Fasteners

Standard Specification for Carbon and Alloy Steel Nuts for Bolts for High Pressure or High Temperature Service, or both. ASTM A194 specification covers a variety of carbon, alloy, and martensitic stainless steel nuts in the size range 1/4 through 4 in. and metric M6 through M100 nominal. It also covers austenitic stainless steel nuts in the size range 1/4 in. and M6 nominal and above. ASTM A194/A194M-17a - Standard Specification for Carbon This specification covers a variety of carbon, alloy, and martensitic and austenitic stainless steel nuts. These nuts are intended for high-pressure or high-temperature service, or both. Bars from which the nuts are made shall be hot-wrought. The material may be ASTM A563 Standard Specification for Carbon and Alloy ASTM A563 Standard Specification for Carbon and Alloy Steel Nuts This specification covers the chemical, mechanical, and dimensional requirements for eight grades (Grades O, A, B, C, D, DH, C3, and DH3) of carbon and alloy steel nuts for general structural and mechanical uses on bolts, studs, and other externally threaded parts.

ASTM A563/A563M-21 Red - Standard Specification for

ASTMA563A563M21Red-Standard Specification for Carbon and Alloy Steel Nuts (Inch and Metric) (Standard + Redline PDF Bundle)- ASTM A563/A563M-21 Red - Standard Specification for Carbon and Alloy Steel Nuts (Inch and Metric) (Standard + Redline PDF Bundle) Carbon Steel Bolts and Nuts Low CS Stud/ Hex Bolt High Carbon Steel Hex Nut (DIA) Metric:M6 - M110; Inch:1/4" - 4.5" AISI 1045 Plain Washer (DIA) Metric:M6 - M110; Inch:1/2" - 4.1/2" Carbon Steel Bolts International Standard:IS, ANSI, ASTM DIN, ISO, JIS, GB, ASME, BS, UNI:Low Carbon Steel Bolts Standard Sizes:M10, M4, M16, M36 M2.5, M6, M30, M12, M8, M14, M2, M3, M20, M24, M5 to M160 Designation:A 563M 04 Standard Specification for Carbon Designation:A 563M 04 METRIC Standard Specification for Carbon and Alloy Steel Nuts [Metric]1 This standard is issued under the fixed designation A 563M; the number immediately following the designation indicates the year of original adoption or, in the case of revision, the year of last revision.

Standard Speci cation for Hardened Steel Washers

ments for Application to Carbon and Alloy Steel Bolts, Screws, Washers, Nuts, and Special Threaded Fasteners 1 This speciÞcation is under the jurisdiction of ASTM Committee F16 on Fasteners and is the direct responsibility of Subcommittee F16.02 on Steel Bolts, Nuts, Rivets and Washers. Current edition approved Aug. 1, 2007. Published August 2007. Standard Specication for Carbon and Alloy Steel Nuts Standard Specication for Carbon and Alloy Steel Nuts [Metric]1 This standard is issued under the xed designation A 563M; the number immediately following the designation indicates the year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. AStandard Specication for Carbons and Alloy Steel Nuts1ments for Application to Carbon and Alloy Steel Bolts, Screws, Washers, Nuts, and Special Threaded Fasteners G 101 Guide for Estimating the Atmospheric Corrosion Resistance of Low-Alloy Steels 2.2 ANSI Standards:1 This specication is under the jurisdiction of ASTM Committee F16 on Fasteners and is the direct responsibility of Subcommittee